Instructions not found for this product, use below instructions Or You can also add instruction by clicking here.
Pin Stadium Installation
Estimated install time is 10-15 minutes
Please note that we are not responsible for any damages done to your pinball machine. Install at your own risk! We suggest that if you are not familiar with working on your pinball machine that you take your time or have someone help you. Always consult your manual for detailed information or have a knowledgeable buddy/technician to help you. If you are looking for Orion’s Belt installation instructions, they are just below this at the bottom of this install section for the Pin Stadiums. If you are installing Pin Stadium Fusion you will simply use the Pin Stadium and Orion’s Belt instructions. Watch this install video and disregard the part near the end where they make the power connection to the machine, as the new version is even easier since you simply plug the power into your service port!! If you are looking for the Hover conversion kit installation Click Here. Or you are installing Baby Pin Stadiums in Munsters Click Here
Step 1
Remove the playfield glass and balls from the machine, then raise the playfield vertical.
The “Standard” tab applies for most all pinball machines. Otherwise click on the appropriate tab if you see the manufacturer of your machine listed.
Next locate your GI and Flasher cables:
GI: Connect the BLUE/WHITE cable’s alligator clips to a GI Bulb (polarity is not important so it doesn’t matter which side you connect them to).
Flasher: Connect the RED/GREEN cable’s alligator clips (polarity does not matter here either)
Note: In some cases the alligator clips may not be able to reach into your desired location. If you are trying to connect to unreachable terminals then please use the wire tap leads lead (small colored stiff wires with black barrel ends). These are great for tapping in the back of a connector terminal. On the opposite end that you plan to clip to, simply fold it over the black barrel so that it has enough width to connect the clip over it. These methods of connection are generally used and can be semi-permanent solutions if done correctly. Optionally if you want a permanent installation then you can solder or wire splice into where you determine is the best location.
Wire tap method shown here:
- Power for ALL JJP Machines: Plug the black power adapter into the service port of your machine located in the bottom of the cabinet inside to the right by the coin door. Due to the tight fit of the playfield support rails on JJP games you will need a small one foot extension cable so that the playfield can be lowered completely. We offer them on our website if you need one or any hardware store etc
-
WOZ
- ECLE(Emerald City LE): Click Here
- Non 2.0 GI/Flashers: Click Here
- 2.0 GI/Flashers: Click Here for the flasher and for the GI you need to connect to Click Here
Location of flashers for all versions of WOZ
Trace the red LED witch flasher wires (it the LED to the right if you are looking down on her from above) to the flat ribbon cable that connects to them. This ribbon cable looks like a 1/4” wide camera film that then goes under the playfield and turns into a red and red/black wire which terminates into a a white 3 pin Molex connectors with blue wires coming out.
Hobbit
- GI/Flashers: Click Here
Dialed In
- GI/Flashers: Click Here
Pirates of the Caribbean
- GI: Option 1: Tap any one of the playfield white spotlights using the wire taps(GI on most all the time) Click Here. Option 2: alternative is with more GI interaction : Click Here You can try either as it is personal preference. I like the spotlights connection personally.
- Flashers: Tap the Light Blue/Black wires going in the shaker motor with the wire taps Click Here
Willy Wonka
- GI: Tap any one of the playfield white spotlights using the wire taps(GI on most all the time) Click Here.
- Flashers: TBD Click Here
Spooky
- America’s Most Haunted, Dominos, Jetsons, Rob Zombie, “Board Power” (backbox top left of board)
- TNA: Click Here (for power run a power cord into the machine from the wall or tap the 110V power source from the machine and add an outlet there)
- Alice Cooper’s Nightmare Castle (ACNC) for the GI trigger find this GI board which is located just behind Frankenstein. Use the wire taps on the Blue and Grey labeled “+” and “G”. For the UV+Glow you will trigger from the shaker motor. If you are installing Fusions the best location to trigger the flashers from are the RGB wires on this harness (trace from the flasher dome on the upper playfield down underneath to this point). Due to the way Spooky has it wired pick up a set of these from Amazon for a clean tap into the wires. Simply separate the wires from each other and done!
Heighway Pinball
- Alien
- Power/GI: Click Here
- Flashers: Trigger the UV+Glow from the terminals on the Xenomorph magnet!
Monster Bash Remake and Attack from Mars:
Monster Bash Remake:
GI: You will use the wire taps to connect into the “BP Moon”. Simply insert one in the “Red” and the other in the “Blue”, then clip onto the other end of the wire tap with the alligator clips from the blue/white Pin Stadium GI cable.
Flasher: The best place is for the Frankenstein flasher. Trace the 2 wires from the purple orbs down to down underneath the playfield to the connector and use the wire taps there by inserting them behind the wire and then clipping on to them with the alligator clips:
Attack From Mars Remake: You will use the wire taps to connect the GI Blue/White cables. Simply unscrew a GI connector (one screw) on AFMR (there are some about halfway down on the right) and then unplug it (machine off to be safe). Now insert the ends of the wire taps into the outside females holes were the GI connectors plug in.
Note: It is best to hold the connector vertical, then insert about 1/8″ of the wire tap end in the hole then bend it over so it hangs. Then do that for the opposite side too.
Note: Polarity does not matter, so as long as you have the wire taps in good, the Pin Stadium GI module will figure out the polarity for you.
Next close up the GI connector on the wire taps while they are inserted (this is why it is important to hold it vertical so that they will stay in as you put the other end of the connector back together). The wire taps are now “pressure fitted” in safely and securely. Now simply bend the opposite ends of the wire taps all the way over on top of the black barrel so that it is thick enough for you to clip the alligator clips onto. (See instructions further down on this page for pictures and an explanation of how to properly use the wire taps).
Good job!!
Now you are ready to connect the Red/Green Pin Stadium Flasher cables to the “Center Saucer” Dome connectors. Trace the wires that come down from the UFO Saucer under the playfield towards the back and you will see a multiple wire connector (in pictures below) that has Yellow and Violet(Purple) wires coming out of it. Simply insert the wire taps in from behind and pressure fit them into each of those. Polarity does not matter here either.
Step 2
Connect the Universal Power (pic below) to the service port of your machine. This is usually located in the bottom of the cabinet by the coin door to the right. If you have a newer Stern machine (Spike 1/Spike2) then it is behind the translite on the lower right side. The plug looks like standard wall outlet.
Note: On some older machines their is may be an adapter cable that might need. Your local computer store should have these or we sell them on our website here: https://pinstadium.com/product/service-port-adapter/
Step 3
Lower the playfield to resting angle position on the cabinet and rest the light bars on the playfield.
Then plug the power connector cable, GI, and Flasher cables into the Pin Stadium GI module as shown below:
Step 4
Place the now connected Pin Stadium GI Module over the backboard into the bottom of the cabinet out of the way of any moving objects.
Next locate the accessory packet and inside of it are small adhesive ribbon cable clamps included to use to attach to the back of the playfield to help guide the ribbon cables. They are to be attached to the furthest upper left and right corners of on the backside of the playfield backboard. These are vital as they act as a guide to keep the cables clear of pinching and allow as a memory for your cable length to help keep the cable tucked away and hidden.
Tip: Bend the ribbon cable in half (as shown below) so that it slides easier in the cable clamp. This allow for easier adjustment for slack and helps when you go to tuck it out of site once the playfield is down. You will eventually find a sweet spot that works with each machine. The ribbon cable is designed to be bendable so that you can further tuck it up and out of the way for a nice stealth look.
Step 5
**IMPORTANT: SKIP this section if you are using the Hover installation kit to mount your lights: Click Here for installation. Otherwise if you are using Magna-Mouunts please continue. Lower the playfield back down to it’s level resting position and use the included alcohol wipe to clean just below the playfield glass track. Positioning of the lights will be 1/8th of an inch below the glass channel. Clean about 2 inches below the glass so not to pick up any stray dust. It will need to be very clean and completely dry before proceeding. The wipe is to insure the best adhesion for the Magna-Mount system that hold the lights to the side of the cabinet. This is a VERY IMPORTANT step as this will insure the Pin Stadium lights a solid mount. Take your time here on this one please. Also DO NOT remove the other side of the Magna-Mounts from the light bar prior to installation. The light bars are to be installed with them on for two important reasons, one for correct positioning and also for polarity of the mounts. If you take them off and install them there is a good chance you will reverse polarity if they are not put on with the light bars. If polarity it wrong light bars will always shift when you re-attached them and never go in the correct spot. The two magnets fight against each other.
Notice here, I have roughly marked the length of the lights to know where to clean and positioning of the lights is critical for the best effect and clean factory finished look. The ribbon cable should be tucked just behind and under the back playfield glass receiver channel.
Step 6
Carefully peel off the white protective backing for the Magna-Mount system, paying attention to align the lights 1/16th inch below the channel and far enough back to hide the ribbon cable and to clear the backbox hinge.
Note: DO NOT separate either of the sides the Magna-Mounts from the back of the light bar as it needs to be installed together as the magnetic polarity is set for proper mounting. This is very important!
Press firmly all along the entire length of the light channel with your fingers to create maximum bonding. Repeat for the opposite side of the cabinet. Take your time here as this is a vital part of the install to insure proper mounting.
Step 7 (Finished)
Restore the playfield to normal play position and replace the balls. Attach the Pin Stadium lights to their Magna-Mount backs on the side of the cabinet. Replace the playfield glass and lockbar.
**Important: Remember to always remove the lights and rest them on the playfield before raising your playfield. They will get potentially get damaged if you do not do this. Try to remind yourself as this is SUPER important especially since you are not used to doing this each time when raising your playfield. If you plan to raise the playfield to a vertical position then we suggest that you wedge the light bars on the playfield safely under a slingshot plastic or habitrail ball return above an inlane. Each machine is different and you will need to find a good spot on each machine to secure them.
FINISHED!!!
Next simply download and install the Pin Stadium app. Click Here!
Enjoy the light show and your new vision of your pinball machine! Please post up your impressions on the Pin Stadium Pinside thread as many others are really wanting to see and hear the results. It would be really great if you can take a picture in the dark of your machine with the lights OFF and then with them ON! Thank you again for your order and support of this product. As always please do no hesitate to email me directly with any questions: [email protected]
Orion’s Belt/Fusion Installation
Estimated install time is 10-15 minutes
Please note that we are not responsible for any damages done to your pinball machine. Install at your own risk! We suggest that if you are not familiar with working on your pinball machine that you take your time or have someone help you. Always consult your manual for detailed information or have a knowledgeable buddy/technician to help you.
For Orion’s Belt in particular it makes things much easier if you go into your machine’s setting and cycle through your flasher lamps (generally under Settings/Diagnostics/Flashers). This will help you to visually identify what flashers are available to trigger. Having your manual handy or downloading one helps a lot too with where to trigger these. As a general rule you can use any bulb/trigger (no switches) that is 4v-24v, such as inlays (that may not go on/off much) or even a shaker motor can be a great spot. Some triggers you choose may go on too much or not enough, so don’t hesitate to experiment and have some fun trying various locations and interesting combinations you never thought of before.
Step 1
Remove the playfield glass and balls from the machine, then raise the playfield vertical.
Next locate your cables:
Connect each of the wires to your desired bulb/trigger point using the alligator clips (polarity is not important so it doesn’t matter which side you connect them to).
Note: In some cases the alligator clips may not be able to reach into your desired location. If you are trying to connect to unreachable terminals then please use the wire tap leads lead (small colored stiff wires with black barrel ends). These are great for tapping in the back of a connector terminal. On the opposite end that you plan to clip to, simply fold it over the black barrel so that it has enough width to connect the clip over it. These methods of connection are generally used and can be semi-permanent solutions if done correctly. Optionally if you want a permanent installation then you can solder or wire splice into where you determine is the best location.
Wire tap method shown here:
Step 2
Connect the Universal Power (pic below) to the service port of your machine. This is usually located in the bottom of the cabinet by the coin door to the right. If you have a newer Stern machine (Spike 1/Spike2) then it is behind the translite on the lower right side. The plug looks like standard wall outlet. Since you will likely have a Pin Stadium already using the service port you will need to use a small power strip or “Y” wall power splitter and plug the Orion’s Belt and Pin Stadium into that. You will need something like this that we sell on our store: https://pinstadium.com/product/multi-splitter/
Note: On some older machines their is may be an adapter cable that might need. Your local computer store should have these or we sell them on our website here: https://pinstadium.com/product/service-port-adapter/
Step 3
Lower the playfield to resting angle position on the cabinet and rest the light bars on the playfield.
Then plug the power connector cable cable into the Orion’s Belt Flasher Module as shown below:
Step 4
Place the now connected Orion’s Belt Flasher Module over the backboard into the bottom of the cabinet out of the way of any moving objects.
Next locate the accessory packet and inside of it are small adhesive ribbon cable clamps included to use to attach to the back of the playfield to help guide the ribbon cables.
*Note: Since you likely have a Pin Stadium kit installed in this machine you will simply use the existing ribbon cable clamps you already have.
They are to be attached to the furthest upper left and right corners of on the backside of the playfield backboard. These are vital as they act as a guide to keep the cables clear of pinching and allow as a memory for your cable length to help keep the cable tucked away and hidden.
Tip: Bend the ribbon cable in half (as shown below) so that it slides easier in the cable clamp. This allow for easier adjustment for slack and helps when you go to tuck it out of site once the playfield is down. You will eventually find a sweet spot that works with each machine. The ribbon cable is designed to be bendable so that you can further tuck it up and out of the way for a nice stealth look.
Step 5
Lower the playfield back down to it’s level resting position and use the included alcohol wipe to clean just below your existing Pin Stadium light bar (put it right next to it so that the Orion’s Belt’s Magna-Mounts are touching the Pin Stadiums mounts). Clean about 1 inches below Pin Stadium light bar really well and make sure all stray dust/dirt is gone. It will need to be very clean and completely dry before proceeding. The wipe is to insure the best adhesion for the Magna-Mount system that hold the Orion’s Belt light bar to the side of the cabinet. This is a VERY IMPORTANT step as this will insure solid mount. Take your time here on this one please. Also DO NOT remove the other side of the Magna-Mounts from the light bar prior to installation. The light bars are to be installed with them on for two important reasons, one for correct positioning and also for polarity of the mounts. If you take them off and install them there is a good chance you will reverse polarity if they are not put on with the light bars. If polarity it wrong light bars will always shift when you re-attached them and never go in the correct spot. The two magnets fight will against each other.
Notice here, I have roughly marked the length of the lights to know where to clean and positioning of the lights is critical for the best effect and clean factory finished look. The ribbon cable should be tucked just behind and under the back playfield glass receiver channel into the existing Pin Stadium ribbon cable clamp.
Step 6
Carefully peel off the white protective backing for the Magna-Mount system, paying attention to align the lights flush to the bottom of the Pin Stadiums HD-Magna Mount (they should be touching)
Note: DO NOT separate either of the sides the Magna-Mounts from the back of the light bar as it needs to be installed together as the magnetic polarity is set for proper mounting. This is very important!
Press firmly all along the entire length of the light channel with your fingers to create maximum bonding. Repeat for the opposite side of the cabinet. Take your time here as this is a vital part of the install to insure proper mounting.
Step 7 (Finished)
Restore the playfield to normal play position and replace the balls. Attach the Pin Stadium lights to their Magna-Mount backs on the side of the cabinet. Replace the playfield glass and lockbar.
**Important: Remember to always remove the Orion’s Belt light cars and rest them on the playfield before raising your playfield. Since you have Pin Stadiums you can simply fold the Orion’s Belts onto the back of the Pin Stadiums so it is only one unit. This makes things much easier. They will get potentially get damaged if you do not do this. Try to remind yourself as this is SUPER important especially since you are not used to doing this each time when raising your playfield. If you plan to raise the playfield to a vertical position then we suggest that you wedge the light bars on the playfield safely under a slingshot plastic or habitrail ball return above an inlane. Each machine is different and you will need to find a good spot on each machine to secure them
FINISHED!!!
Now enjoy the light show and your new vision of your pinball machine! *Please Note: Orion’s Belt comes pre-programmed for instant plug and play enjoyment! These instructions are for further optional customization. The factory default setting for the lights are Green, Blue, Red, and White. However to the great thing about them is that you can program the lights to whatever color you would like on the color wheel.
Here are the instructions on how to do this but you will need set up and connect to the Orion’s Belt WiFi first with your mobile device after you download the Pin Stadium app. Click HERE
Once you have completed that then rename your Orion’s Belt to something like “Tron(OB)” to differentiate it (notice the “OB” added for Orion’s Belt) from the Pin Stadium on that machine. Then follow these directions to program and customize your flasher colors:
1. Press “Preview” button- Leds will flash “White” once to indicate entry into programming mode
2. Use the Pin Stadium app to adjust color and brightness settings to your desired preference
3. Press the “Set” button corresponding to the desired Flasher/Spectrum button (1-4) you would like to store. LEDs will flash to confirm saved setting.
4. Repeat Steps 2 and 3 for additional presets if desired (other presets will be retained if not modified)
5. Press “Preview” button again to store presets. LEDs will flash “White” 2x to indicate completion of process !!
*Note: Factory settings out of the box are:
#1: Green
#2: Blue
#3: Red
#4: White
Tip: Not only can you can adjust the brightness of the individual flashers by using the above programming method in the app, but for on the fly across the playfield results you can adjust the brightness of your Pin Stadiums to increase/decrease the overall contrast of the GI versus flashers of the Orion’s Belt flashers.
Please post up your impressions on the Pin Stadium Pinside thread as many others are really wanting to see and hear the results. A short video of them action would be awesome! As always if you have any questions please do not hesitate to email me at : [email protected]